handlebar and brake setup

New to Cycling? Want some advice? Start here...
User avatar
Sprool
Posts: 958
Joined: Sun Sep 09, 2012 19:32 pm

handlebar and brake setup

Postby Sprool » Thu Nov 08, 2012 23:58 pm

I'm looking for some advice on checking set up of handlebars and brakes. Are there any rules-of-thumb or starting points for setting up correct angle/rotation of the bars, and position of the brakes and hoods for most efficient and stress-free riding? I'm just not comfortable with my current setup and feel it needs some fettling, but not sure which way to move.

User avatar
danmitch
Posts: 47
Joined: Tue Apr 03, 2012 16:15 pm
Contact:

Re: handlebar and brake setup

Postby danmitch » Fri Nov 09, 2012 08:52 am

There is an article here http://ruedatropical.com/2009/03/road-d ... -geometry/ which might give some guidance and good starting points for position. I would make sure the reach to the bars is correct firstly without worrying about the brake position.

User avatar
Sprool
Posts: 958
Joined: Sun Sep 09, 2012 19:32 pm

Re: handlebar and brake setup

Postby Sprool » Fri Nov 09, 2012 09:24 am

thanks for the link, a very useful read. Going by the diagrams on the site he's setting up the bars so the line of the drops remains horizontal. All the photos of bikes I've seen has the drops angled down pointing towards the rear axle, so that the tops and rounds remain in the horizontal plane.
Is there any general advice or common practice about this, or is it just whatever feels most comfortable to the individual?

User avatar
Sprool
Posts: 958
Joined: Sun Sep 09, 2012 19:32 pm

Re: handlebar and brake setup

Postby Sprool » Fri Nov 09, 2012 10:08 am

I prepared some diagrams based on ruedas graphics;
Image
A= horizontal drops
B= horizontal tops and brake hoods
C= horizontal tops and upwards brake hoods
D= mid-rotation bars and level hoods
E= mid-rotation bars and upwards hoods.

What is the collective wisdom about the best neutral position to start with?

User avatar
CiB
Posts: 5780
Joined: Fri Sep 05, 2008 08:24 am

Re: handlebar and brake setup

Postby CiB » Fri Nov 09, 2012 11:24 am

A good start point is to have the hoods horizontal as that's where you'll spend most of your time. If they angled down your hands will be sliding forwards so you have to grip the hood, and if they're pointing up your wrists are twisted upwards.

The drops can be where you find them most comfortable; I wouldn't obsess about having them parallel to the floor though.

Start with that and progress.

racingcondor
Posts: 1431
Joined: Thu Jul 30, 2009 17:20 pm

Re: handlebar and brake setup

Postby racingcondor » Fri Nov 09, 2012 12:51 pm

A lot of this depends on the shape of your bars.

Classic bar shapes have a pretty symmetrical C shaped curve so the horizontal drops option works.

My Deda Zero100 have a shape more like a stretched 7 so I go with horizontal tops and hoods. Personally with most modern bars I'd start with that position and adjust from there for comfort or if the particular bar/brifter combination had a particularly lumpy join.

User avatar
Monty Dog
Posts: 20383
Joined: Thu Dec 14, 2006 14:31 pm

Re: handlebar and brake setup

Postby Monty Dog » Fri Nov 09, 2012 18:01 pm

Depends on the shape of the handlebar first and then the shape of the shifter to get the optimum position. As I spend most of my time on the hoods / tops then I optimise my bar/lever postion for this - tops are a shade below horizontal and the hoods extend horizontally to make a broad, horizontal platform for my hands and wrists - between D and E. I only ride on my drops when seriously hammering as it's quite a 'deep' position.
Make mine an Italian, with Campagnolo on the side..

User avatar
Sprool
Posts: 958
Joined: Sun Sep 09, 2012 19:32 pm

Re: handlebar and brake setup

Postby Sprool » Fri Nov 09, 2012 19:09 pm

I've tweaked mine back up to a position midway between C and E this afternoon, I'll see how it goes tomorrow on some pretty stiff cycling round Holme Moss. I'm just not getting comfortable in the drops, think I'm trying to find an excuse for buying more bling. I really want to try out one of those flat ramp bars, move away from the traditional C or D curve.

User avatar
MikeWW
Posts: 684
Joined: Mon Jun 15, 2009 09:53 am
Contact:

Re: handlebar and brake setup

Postby MikeWW » Fri Nov 09, 2012 20:04 pm

Last 2" of drops parallel to the ground.Then adjust the hood so they are angled slightly upwards.


Return to “Road Beginners”

Who is online

Users browsing this forum: No registered users and 4 guests