chain is rubbing and catching on next gear help???

Sorting out your thrunge brackets, fettling your inter-rositers and even stuff about bike parts.
User avatar
mike hunts alpine
Posts: 690
Joined: Mon Aug 19, 2013 18:34 pm

chain is rubbing and catching on next gear help???

Postby mike hunts alpine » Sun Oct 06, 2013 20:13 pm

Apologise in advance as its probably just one of those give that a tighten things. (newbie) Slx rear mech on week old bike btw. When pedalling chain is rubbing on next gear up and catches when back pedalling. This has just started since my last ride in extremely wet weather. Can someone please give me idiot proof instructions to fix this.
Cheers.

User avatar
mike hunts alpine
Posts: 690
Joined: Mon Aug 19, 2013 18:34 pm

Re: chain is rubbing and catching on next gear help???

Postby mike hunts alpine » Sun Oct 06, 2013 20:23 pm

Gear 10, chain slightly catches on 9 and so on right the way up.

User avatar
97th choice
Posts: 2248
Joined: Sat Oct 24, 2009 21:37 pm

Re: chain is rubbing and catching on next gear help???

Postby 97th choice » Sun Oct 06, 2013 20:27 pm

Take a look at the FAQ's for this section, you should read up on rear derailleur adjustment in park tools or Sheldon brown which is good.
Too-ra-loo-ra, too-ra-loo-rye, aye

Giant Trance
Radon ZR 27.5 Race
Btwin Alur700
Merida CX500

User avatar
cooldad
Posts: 28212
Joined: Sat Apr 17, 2010 22:01 pm

Re: chain is rubbing and catching on next gear help???

Postby cooldad » Sun Oct 06, 2013 20:35 pm

Read Parktools and adjust. And don't pedal backwards.
I don't do smileys.

There is no secret ingredient - Kung Fu Panda

London Calling on Facebook

Parktools

User avatar
The Rookie
Posts: 23083
Joined: Thu Apr 30, 2009 09:29 am

Re: chain is rubbing and catching on next gear help???

Postby The Rookie » Wed Oct 09, 2013 12:20 pm

mike hunts alpine wrote:Gear 10, chain slightly catches on 9 and so on right the way up.

10 is the smallest rear gear, 9 next smallest and then you go further DOWN.....

So which end of the cassette is it?

Will always catch back pedaling as there is nothing to guide it, correct indexing should sort the issue pedaling forwards.

User avatar
bladeone
Posts: 76
Joined: Thu Jan 24, 2013 10:35 am

Re: chain is rubbing and catching on next gear help???

Postby bladeone » Wed Oct 09, 2013 15:07 pm

Just had that prob with mine mentioned it on first service usually I can tune them out myself but this wasn't happening on this occasion, anyhow turns out the freehub is causing the rear cassette to oscillate resulting in lazy/miss shifts may not be your problem but worth having a look.
YT Capra Pro Race
Trek Remedy 2013 (sold)
Cube Reaction GTC Pro (sold)
Gary Fisher Hoo Koo E Koo

*AJ*
Posts: 1051
Joined: Thu Aug 27, 2009 11:15 am

Re: chain is rubbing and catching on next gear help???

Postby *AJ* » Thu Oct 10, 2013 12:04 pm

If its rubbing on the next biggest gear id say there is too much tension in the cable (assuming its not rapid rise).

There's also the possibility of the rear mech hanger being bent inwards. (id check this first by looking down the bike from the rear to the front and make sure the mech is hanging straight down not angled)

If the hanger is straight then check the cable routing, if the cable outer has popped out of one of the guides it can put more tension on the inner cable, or if they are twisted they don't run smooth and cause problems.

Another thing to check is the barrel adjuster on the shifter? has this been wound out? if it has then tension has been added to the cable and may need winding back in:-
* If it has been wound out then put the bike in gear '5' and make sure the shifter is also in 5
* look down the bike from the rear and see where the top jockey wheel is in relation to the cog it wants to be guiding it to.
* The top jockey wheel should be perfectly inline with cog '5' on the rear. If there's too much tension then the mech will be slightly further towards cog '4' and if there's not enough tension it will be further towards cog '6'.
* Adjust the barrel adjuster on the shifter to move the mech over (wind out to add tension, in to reduce tension).

If adjuster is wound all the way in then drop the rear gear into 10, make sure both the shifter and the chain are in '10' then undo the pinch bolt holding the cable and allow the cable to become loose, then refit it, pulling it tight, but not really tight (just hold the cable between your fingers and do up the pinch bolt again) then fine tune with the steps I described above.

User avatar
mike hunts alpine
Posts: 690
Joined: Mon Aug 19, 2013 18:34 pm

Re: chain is rubbing and catching on next gear help???

Postby mike hunts alpine » Sun Oct 13, 2013 10:50 am

The Rookie wrote:
mike hunts alpine wrote:Gear 10, chain slightly catches on 9 and so on right the way up.

10 is the smallest rear gear, 9 next smallest and then you go further DOWN.....

So which end of the cassette is it?

Will always catch back pedaling as there is nothing to guide it, correct indexing should sort the issue pedaling forwards.

Its slightly catching on the bigger gear all the way up.
Tried loosening and tightening the cable and its still catching.

User avatar
cooldad
Posts: 28212
Joined: Sat Apr 17, 2010 22:01 pm

Re: chain is rubbing and catching on next gear help???

Postby cooldad » Sun Oct 13, 2013 10:57 am

cooldad wrote:Read Parktools and adjust. And don't pedal backwards.
I don't do smileys.

There is no secret ingredient - Kung Fu Panda

London Calling on Facebook

Parktools


*AJ*
Posts: 1051
Joined: Thu Aug 27, 2009 11:15 am

Re: chain is rubbing and catching on next gear help???

Postby *AJ* » Tue Oct 15, 2013 11:27 am

Hanger bent?????


Return to “MTB Workshop & Tech”

Who is online

Users browsing this forum: Crazyjenkins01 and 1 guest