Check out Joe Breeden's Intense Racing UK M16C

Junior downhiller and Intense Racing UK rider show us his weapon of choice

Fresh faced Joe Breeden is known for his smooth unflappable style. At only 17 years of age he's already bagged a succession of impressive race seasons, with a ninth place debut in the Downhill World Champs, strong results in the British Downhill Series and an outright win of the junior category at the Welsh DH Championships all behind him.

2017 is set to turn things up a notch as Joe guns for the junior category of UCI World Cup competition. Racing as part of Intense Racing UK, a newly formed team by UK distributor Saddleback, Breeden will join team manager and Elite competitor Olly Morris, fellow racer Charlie Hatton, veteran Andrew Titley and Women's DH competitor Jess Greaves in an assault on the UCI World Cup.

The M16C can be configured to run in 216mm (8.5in) or 241mm (9.5in) travel modes
The M16C can be configured to run in 216mm (8.5in) or 241mm (9.5in) travel modes

Another arm of the same team will see Enduro racers Sam Flockhart and Ajay Jones tackle numerous enduro events including the Enduro World Series, with Andrew Titley also lending his hand at the discipline.

Saddleback brings some of mountain biking's most desirable products into the UK, with the likes of Intense Cycles, Troy Lee Designs, ENVE, Rotor and Chris King on its books. 

Another look at Astute's distinctive mudline VT saddle
Another look at Astute's distinctive mudline VT saddle

It should be no surprise, then, to see that Breeden's Intense M16C is jam-packed with kit from many of the above names. In truth, his Intense M16C doesn't stray wildly from the £10,500 build you or I could purchase off the peg, at least not in these pictures anyway. 

We ended up getting early access to this team bike at a launch event last week, meaning the build isn't 100 percent there yet. Specifically, the SRAM chainset will be switched out in favour of Rotor's all-new HAWK crank and BB, which will allow him to use Rotor’s oval chain rings.

Another difference from the factory build is with the wheelset, with Saddleback switching out the standard DT Swiss hubs for Chris King ISO SD/DH models.

SRAM's X01 DH 7-speed transmission leaves no excess cogs
SRAM's X01 DH 7-speed transmission leaves no excess cogs

Personal tweaks to the bike include an extension over the reach offered by the regular XL frame size, to better suit Breeden's lanky frame. That's been achieved through the use of a +6mm Works Components Reach Adjust Headset. Breeden also trims his ENVE Minaar Bar V2 down to 770mm rather than the standard 808mm length. 

Contact points are about as personal as things get, and Breeden prefers Renthal lock-on grips, Steve Peat signature Crank Brothers Mallet pedals and Saddleback-stocked brand Astute's Mudline VT saddle. The complete build totals just 34lbs (15.4kg).

We'd like to wish Joe and the rest of the Intense Racing UK Team a brilliant season ahead.

Not so much as a scratch on the the levers of Breeden's Guide RS brakes
Not so much as a scratch on the the levers of Breeden's Guide RS brakes

  • Frame: Intense M16C Factory 27.5”, 215-240 mm travel, XL
  • Rear shock: RockShox Vivid Coil
  • Fork: RockShox Boxxer World Cup, 200 mm
  • Headset: Works Components Headset (+ 6mm reach)
  • Stem: ENVE Carbon direct mount
  • Handlebar: ENVE Minaar Downhill Bar V2, 808mm (cut down to 790mm)
  • Grips: Renthal Lock-On Grip
  • Front brake: SRAM Guide RS, 203mm rotor
  • Rear brake: SRAM Guide RS, 203mm rotor
  • Rear derailleur: SRAM X01 DH 7-speed
  • Shift levers: SRAM X01 DH 7-speed
  • Cassette: SRAM XG-795 10-24, 7 speed
  • Chain: SRAM X1
  • Chain Guide: E Thirteen LG1+
  • Crankset: SRAM X01 (soon to be Rotor HAWK & oval ring)
  • Bottom bracket: BSA (threaded) 83mm SRAM (soon to be Rotor)
  • Pedals: Crankbrothers Steve Peat Signature Mallet
  • Wheelset: ENVE M90 (Chris King ISO SD/DH hubs)
  • Front tyre: Maxxis Minion DHF 3C Maxxgrip DH casing, 27.5in x 2.5in
  • Rear tyre: Maxxis Minion DHF 3C Maxxgrip DH casing, 27.5in x 2.5in
  • Saddle: Astute Mudline VT
  • Seatpost: ENVE, 31.6 mm, zero offset
  • Complete weight: 34lbs (15.4kg)

Critical measurements

  • Rider's height:  6ft 2in (188cm)
  • Rider's weight: 68kg (150lbs)

Geometry details

  • Top tube length (effective): 25in.2 (640mm) (including 6mm of reach extension from headset)
  • Seat tube length: 18in (457mm)
  • Head tube length: 5.2in (132mm)
  • Head tube angle: 63.5
  • Seat tube angle (effective): 73.3
  • Stand over height: 32.1in (816mm)
  • Chainstay length: 17.5in (445mm)
  • Wheelbase length: 50in (1271mm) (including 6mm of reach extension from headset)

Related Articles

Back to top