Martin Maes' EWS-winning GT Sanction

The juicy details on the Enduro World Series winner

In a way, it seems ridiculous that it’s taken this long for Martin Maes to win a round of the Enduro World Series. He’s had the pace for a long time and has come close more than once; and yet, quite unbelievably, he’s still only 19 years old. He’s not even officially old enough to compete in the senior field.  But he chose to anyway, and that decision payed off here in Finale Ligure, as the young Belgian took the win in style at the final round of the 2016 season.

Straight after the race, we caught up with Martin and his team-manager/mechanic, Mark Morrison. He gave us the juicy details on the bike Martin rode to victory.

The frame

At around 186cm tall (Mark estimates), Martin rides a size-large GT Sanction. It’s totally stock, with a standard FSA headset, and no offset shock bushings. With a 170mm travel Fox 36 fork, we measured the head angle at a tick under 66 degrees. So far, so normal.

Suspension

Martin was running a Fox Float X rear shock, which is apparently what he uses all the time. We asked if he’s experimented with Fox’s Float or coil X2 shocks, but according to Mark: “there’s a good feeling with this shock, and it’s got lockout for the climbs too.”

It took a little sleuthing to find out how Martin’s suspension was set up
It took a little sleuthing to find out how Martin’s suspension was set up

As for suspension setup, Martin is running 200Psi in the shock, with 73Psi in the fork. The off-the-shelf shock (no custom tuned damper here) was set to its lightest compression setting when we checked the bike over, while the fork’s Low-speed compression was set 16 clicks from closed (8 from fully open), and the High speed compression was set up pretty light at 18 clicks from closed (4 from fully open).

Mark was coy about revealing how many volume spacers were fitted, but we had a quick bounce on the bike and found the fork was decidedly on the progressive side. We’d guess at least two of Fox’s orange volume spacers were fitted.  We also noticed the rebound speed was moderate, neither particularly fast or slow, and was extremely well-balanced front to rear.

Tyres

While many EWS racers chose fast-rolling rear tyres for the pedally stages on the second day of the race, Martin chose to run cut-down mud spikes. The Schwalbe Dirty Dan’s outermost knobs have been removed completely, while the rest of the tread is trimmed to suit the course – flatter tracks get shorter tread for less rolling resistance.

Schwalbe Dirty Dan tyres are cut down for faster rolling
Schwalbe Dirty Dan tyres are cut down for faster rolling

These tyres use Schwalbe’s stickiest ‘Vertstar’ rubber mix with a full-fat DH casing, which is even beefier than its popular ‘Supergravity’ tyres. Mark explains: “we need all the protection we can get with Martin!” Despite this, Mark claims that once he’s cut them down they actually roll faster than a stock Magic Mary (Schwalbe’s popular mixed-conditions tyre). We asked him if they’d tried a cut-down Magic Mary, but apparently Maes prefers the feel of the narrower Dirty Dan.

Tyre pressures are set to 24psi in the front and 26psi in the rear, which apparently doesn’t change much from race to race.

Wheels

According to Mark, Martin uses Stan’s alloy Flow EX rims 90% of the time. They have experimented with using the brand’s lighter Bravo carbon hoops, most often on the front, but feel that an Aluminium rim is more likely to survive a race, albeit with the occasional dent.

Mark explains that when building wheels for Martin, he keeps the spoke tension on the lighter side. This is to provide more compliance and comfort from the wheel whilst also allowing it to deform under impact, which he says reduces the risk of breaking a wheel.

Only alloy wheels can be trusted to withstand the abuse Martin gives them
Only alloy wheels can be trusted to withstand the abuse Martin gives them

The tyres are setup “straightforward tubeless” (no Procore or other in-tyre tricks). Mark revealed that the rims are built up with “secret layers of tape to hold the tyre very very tight on the rim and give a very low rim-edge so it’s hard to puncture by snake bite.”

Cockpit

A 50mm Raceface Atas stem is paired with a 780mm Raceface SixC bar, which measures up at closer to 790mm when shod with ODI Elite Motion grips.

A 50mm stem and 780mm bar sit above 20mm of spacers
A 50mm stem and 780mm bar sit above 20mm of spacers

The bar uses the 35mm clamp diameter, which apparently keeps things stiff enough for Maes near the stem, while still allowing enough compliance towards the ends. Combined with a generous 20mm of spacers under the stem, the 20mm rise bar results in a fairly high bar for a rider of Maritn’s height, at 1055mm measured from the ground.

The details

We spotted that Martin’s CrankBrothers Mallet E pedals use the longer than standard axles, offering extra clearance from the crank. He uses 170mm Shimano XTR crank arms, with a 34 tooth chainring and a standard 11-44 tooth XTR cassette. No need for dinner-plate gears here!

The longer axles space Martin’s Mallet E pedals further away from the crank
The longer axles space Martin’s Mallet E pedals further away from the crank

Maes’ 150mm KS Lev dropper post sits almost flush with the top of the seat tube, where a Hope seat clamp is laser-etched with his name. Shimano Saint brakes are used front and rear, each clamping 180mm rotors, and the fork uses a 20mm thru axle.

There’s just enough room for a 150mm travel seat post. Martin’s name is etched onto the seat clamp so he knows which bike is his
There’s just enough room for a 150mm travel seat post. Martin’s name is etched onto the seat clamp so he knows which bike is his

The weight? Well, this is a bike that’s set up to survive some serious punishment. We weighed it at 14.9Kg, (32.8lbs). That’s including pedals and the obligatory inner tube strapped to the frame.

Would it even be Enduro without a tube strapped to the frame?
Would it even be Enduro without a tube strapped to the frame?

Seb Stott

Technical Writer, UK
Seb is a geeky technical writer for BikeRadar, as well as MBUK and What Mountain Bike magazines. Seb's background in experimental physics allows him to pick apart what's really going on with mountain bike components. Years of racing downhill, cross-country and enduro have honed a fast and aggressive riding style, so he can really put gear to the test on the trails, too.
  • Discipline: Mountain
  • Preferred Terrain: Steep!
  • Current Bikes: Focus Sam 3.0, Kona Process 111, Specialized Enduro 29 Elite
  • Dream Bike: Mondraker Crafty with Boost 29" wheels, a 160mm fork and offset bushings for maximum slackness.
  • Beer of Choice: Buckfast ('Bucky' for short)
  • Location: Bristol, UK

Related Articles

Back to top