How to build and jump a mini kicker

Pro tips on building a portable ramp and jumping (and landing) it

Professional mountain biker and Action Sports Tour rider Tom Cardy shows us how to build a mini kicker to create a stepdown and then how to jump and land it.

How to build a mini kicker

A mini kicker
A mini kicker

1. Materials and tools

You need two sheets each of 18mm and 9mm plywood, 4–6 lengths of 4x2 CLS timber and some screws.

You also need a hand saw, jig saw, tape measure, ball of string, marker pen, square and a drill.

2. Shape the sides

My ramp is 6-foot long, 3-foot tall and has a radius of 8-foot. Tie your pen to an 8-foot length of string. On the 18mm ply measure 6-foot along the bottom and 3-foot high so you have what looks like half a rectangle.

On the opposite side to where you marked the 3-foot, put the pen on the bottom line at your 6-foot mark and get someone to hold the end of the string nice and tight, then draw from the bottom of the 6-foot mark to the top of the 3-foot mark to create a curve on the ply.

Cut the side out and use it as a template to cut an identical one from the other sheet.

3. Bracing

Cut your 4x2 timber into lengths, say about 3-foot, to determine the width of your ramp. Screw these between the two sides, flush with the curve about 5-inch apart, to make the ramp nice and sturdy. Cut a few extra ones to brace the back too.

4. Ply and ride!

Cut your 9mm ply into sections to fit the curved front of the ramp, laying it on the braces and screwing it into the 4x2 timber. Remember to take the curve into account when measuring the ply.

Start screwing at the top and work your way down to ensure it’s flat. If there’s any ply sticking out the top, trim it flush.

How to jump a mini kicker

xxxxx
xxxxx

1. Kicker set-up

Here we’re using the kicker as a stepdown, with a grass bank as the landing ramp.

Before you even think about jumping, first analyse the situation. Here the run-up is slow and bumpy because it’s grass, the landing is lower than the take-off and the run-out is quite sketchy.

2. Approach

When you’re a good distance from the ramp have one last look around to make sure it’s all clear, then commit.

Pedal at the speed you need to clear the jump — depending on the run-up you may need to give it some.

3. Out the lip

Jumping a stepdown, you want to ride the kicker like a normal tabletop jump or a double.

As you take off have your eyes on your landing point already, pull up on the bar and just nicely level out.

I like to keep it chilled and save the tricks until I get comfortable riding the set-up.

4. In the air

To start with there’s no need to go too high or crazy, just keep loose, stay level and keep a close eye on your landing.

The thing with riding kickers is that most have never been ridden before and they can be sketchy, so always err on the side of caution. Once you get more confident you can add some style.

5. Landing

In this case it’s going to be like a landing on a double, so try to land with both wheels together. As you come into the landing absorb the impact by bending your knees and elbows.

Bear in mind the grass bank may not be smooth, so hold on tight.

Tom’s tips

Test your kicker: Before jumping, try the ramp out on flat ground first to make sure you’ve made it a good shape and you know what it’ll feel like.

Start steady: Don’t make the gap too big to start with — you can work your way up to the Rampage canyon gap! The only things that’ll change are your speed and landing.

Safe landings: Check your roll-out is safe and clear before you jump. If it’s a hard landing or you’re jumping to flat, drop your rear wheel slightly to lessen the impact. Brace yourself more if it’s a big gap!

This article was originally published in Mountain Biking UK magazine, available on Apple Newsstand and Zinio.

Related Articles

Back to top