Traditional tubular tyres continue to rule the roost at the top levels of cyclocross racing, and for good reason: the wheels and tyres are lighter, the casings tend to be suppler and do a better able of conforming to the ground. Most importantly, they can be reliably run at traction-enhancing pressures that typical clinchers can only dream of – sub-20psi in some cases.
For those who can’t be bothered with the hassle and expense of tubulars, though, tubeless setups are a tempting alternative with no tubes to pinch and the ability to swap tyres quickly with changing course conditions. Even better, running sealant automatically repairs small punctures, too, meaning fewer visits to the pits.
“I was a little skeptical at first but I haven’t had any issues with burping or rolling any tyres, and that was definitely a concern at speed when you’ve got just 28 or 25psi,” said Jake Wells, who made the move to the Stan’s NoTubes factory cyclocross team and Kenda tubeless clinchers in 2011, after racing on tubulars for years.
“I’m running the exact same pressures as I was running on tubulars,” he continued to BikeRadar. “I don’t like my tyres to be really foldy anyway – 24psi is about as low as I like to go, but some of the girls on the team are running around 22 or 24psi pretty consistently.
“[Tubeless] makes it a much more versatile setup, especially for someone who doesn’t have a truck full of wheels and tyres ready to go. I’ve got two bikes and I just bring extra tyres in my bike bag.”
Tubeless options are more plentiful than ever these days – and some of them even work. Here are some tips, guidelines, and words of caution to help you ditch the tubes.
It’s all about the fit
A tubular tyre is (hopefully) securely glued onto a rim and a tubeless mountain bike tyre’s high volume produces enough force to hold the tyre and rim together firmly. But a tubeless cyclocross tyre enjoys neither of those benefits, occupying an unfortunate no man’s land in terms of reliability.
As such, it’s all about the quality of the interface between the rim and tyre. Tighter is better, because the physical interlocking of the two pieces is nearly the only thing holding the system together. Good omens include reassuringly loud ‘pops’ during inflation (as the bead seats onto the rim), tyres that easily inflate with a floor pump, and tyres that are difficult to remove once deflated.
Companies such as kenda are now specifically developing certain cyclocross tires to be tubeless friendly: James Huang/Future Publishing
Companies such as Kenda are developing certain cyclocross tyres to be tubeless friendly
Not surprisingly, we’ve had the most consistent good luck using rims and tyres that are specifically intended for tubeless applications, such as wheels and rims from Stan’s NoTubes, Shimano, Easton, Bontrager, and Campagnolo/Fulcrum mated with tubeless-ready tyres from Vittoria, Kenda, and Hutchinson plus about 30cc of latex-based sealant.
In the case of the Shimano, Easton, Bontrager, and Campagnolo/Fulcrum wheels – or any others that display the ‘Road Tubeless’ badge – it’s a matter of the rim and bead dimensions being designed to work and fit tightly together, with purpose-built geometry on both sides of the interface.
Stan’s NoTubes and American Classic rims, on the other hand, use a bead hook diameter that’s slightly larger than standard, resulting in a tighter-than-usual joint and the extra security that tubeless setups require.
We’ve also noted better tyre security (and lower successful operating pressures) on rims with wider profiles. The extra sidewall support helps combat tyre roll at lower pressures, and the broader foundation also opens up the tyre to create a bigger footprint and more air volume – which simultaneously creates more retention force for a given inflation pressure.
Non-tubeless-specific combinations can work, too, but it’s a far less consistent pairing that needs to be evaluated on a case-by-case basis. Skinwall tyres should generally be avoided for tubeless applications, regardless of the fit, as the sidewalls are usually too porous to seal.
In general, here is a good rule of thumb: if the wheel and tyre combination you’re trying to set up tubeless is very easy to install (or, worse, essentially tries to fall off the rim) or virtually impossible to inflate even with an air compressor, stop now and continue reading.
Making it work
A little diligence can turn a marginal setup into one that’s much more reliable – but, again, the key is the quality of the fit. The usual culprit is either a tyre that’s too loose or a rim that’s effectively too small. Trying other brands of tyres will confirm if your problem is the former, at which point we advise cutting your losses. Conversely, building up the rim bed to increase its effective diameter is comparatively easy.
Pre-formed rim strips can get the job done (such as the molded rubber rim strips from Stan’s NoTubes) but we prefer NoTubes’ airtight yellow tape, which is offered in multiple widths to provide a proper edge-to-edge fill. Plus, since it’s very thin and comes on a roll, you can add only as much as you need. Simply apply layers of tape to the rim bed until the tyre sits reasonably snug without air, making sure to overlap the tape at the valve hole on each pass.
Once the rim bed is built up to a suitably large diameter, the tyre might be hard to install (a reassuring sign) but it should reward your inflation efforts with that series of ‘pops’ we described earlier.
Another alternative is to use your own airtight, bead-to-bead, rubber rim strip using a 20in-diameter inner tube – preferably one with a removable Presta valve core. Make sure to lay down a non-stretch rim strip first, if your rim has conventional spoke holes drilled.
Rims that aren’t designated as tubeless can sometimes still be used as such, with a little bit of work. here, an airtight rim strip has been made out of a 20in inner tube: James Huang/Future Publishing
An airtight rim strip made out of a 20in inner tube
Split the tube longitudinally down the middle, leaving the valve in the center of the resultant strip. Insert the stem into the valve hole and then stretch the tube evenly around the rim. Carefully install the tyre over your homemade rim strip, inject approximately 30cc of sealant through the valve, and inflate away.
Providing the rim bed was sufficiently large in diameter to begin with, subsequent inflation should be pretty easy. But keep in mind that an initial tight fit is still critical. Otherwise, you’ll have an airtight seal that’s still prone to burping under load. Also, this method is a one-shot deal as it isn’t likely you’ll be able to reuse the strip.
Regardless of the method you choose, there are a few tricks you can use to help get the tyre initially inflated. Coating the tyre beads with soapy water helps create an initial seal (we keep a spray bottle filled in our workshop specifically for this purpose), and removing the valve core during inflation allows for a higher flow rate.
Yes, using an air compressor certainly makes things easier but better-fitting rim and tyre combinations also tend to be easier to inflate with a conventional floor pump, which ensures a higher degree of field serviceability.
According to Mike Bush at Stan’s NoTubes, CO2 cartridges should be avoided either way. They’ll seat the tyre but will also react with the sealant inside. Instead, he recommends using Genuine Innovations’ Big Air! canisters, which are charged with compressed propane.
Hit the barriers – but check your work first
Even when tubeless cyclocross tyres are set up optimally, they still can’t match the overall performance of tubulars. However, they’re a reasonable compromise for the weekend warrior and – assuming you’ve achieved a reliable setup – better than conventional clinchers in most respects.
We’ve been able to run pressures as low as the mid-20s in local races with no burping – even on a few instances when we felt the tyre roll beneath us in hard corners. Thorny tracks become a non-issue too, as the sealant inside the tyre easily repairs small punctures without you having to visit the pits.
If you’ve done it right, the tire can actually fold completely beneath you without breaching the seal. get it wrong, however, and the results can be catastrophic: James Huang/Future Publishing
If you’ve done it right, the tyre can fold completely without breaching the seal
That said, it’s critical to check your work thoroughly before heading out, since tubeless cyclocross setups are still a less-than-precise science and the consequences of failure can be severe.
We recommend deflating your tyre to around 10psi, placing the wheel at an angle on a surface with good grip, and then forcefully side-loading it – just as you would in a hard corner. If it holds tight without burping, you can be fairly confident you’ve got a good setup. If not, use at your own risk.
Words of warning
In any event, none of the above conversions are recommended for use on road tyres, where proper road tubeless wheels and tyres must be used unless you want to risk a catastrophic blowout.
Most importantly, approach the project deliberately and proceed with caution. There’s no guarantee of success but the chances are good if you’ve got all the right ingredients: wide rims, tight tyre-to-rim interfaces, and ‘cross tyres with tubeless-ready beads. Nail the formula and you’ll enjoy lower rotating weight, fewer flats, better traction, and improved ride quality as compared to conventional clinchers, all without having to resort to tubulars – yet.